FailureAction does not work since P3DV5.1.

Discussion related to Mission design and creation.
Post Reply
andi20
Posts: 10
Joined: Fri Jun 18, 2021 12:20 pm

FailureAction does not work since P3DV5.1.

Post by andi20 »

I have to report an important error in P3d V5.2: FailureAction does not work since P3DV5.1.

With P3DV5.03 everything worked, from P3dV5.1x not anymore.
I have hoped that it is fixed with V5.2. Unfortunately it does not work also in V5.2.

With P3DV5.03 it looked like this: (Red frame shows current selection, Blue frame the selection options):
https://andi20.ch/p3d/failureaction/P3dV5.jpg

With P3DV5.1 / V5.2 it looked like this: (Red frame shows current selection, Blue frame the selection options).
https://andi20.ch/p3d/failureaction/P3d52.jpg
Greetings
andi20 (Jörg)
andi20
Posts: 10
Joined: Fri Jun 18, 2021 12:20 pm

Re: FailureAction does not work since P3DV5.1.

Post by andi20 »

Unfortunately, the FailureAction still doesn't work for me, even in the latest version 5.4 (5.4.9.28482).

A mission created with version 5.0 (5.0.31.35253), which works correctly with 5.0, brings the following error message in 5.4:
https://andi20.ch/p3d/failureaction/Error.jpg

im "ObjectLoadErrors.txt" steht folgendes:
Fire aus 1 Error: Missing entity ObjectReference
Fire Wasser 2 Error: Missing entity ObjectReference
Fire Wasser 1 Error: Missing entity ObjectReference
OilLeak Wasser 2 Error: Missing entity ObjectReference
OilLeak Wasser 1 Error: Missing entity ObjectReference
EngineOilLeak 2 Error: Missing entity ObjectReference
EngineFire 1 Error: Missing entity ObjectReference
Cylinder 6 Error: Missing entity ObjectReference
Cylinder 5R Error: Missing entity ObjectReference
Cylinder 5 Error: Missing entity ObjectReference
Cylinder 4R Error: Missing entity ObjectReference
Cylinder 3R Error: Missing entity ObjectReference
Cylinder 2R Error: Missing entity ObjectReference
Cylinder 1R Error: Missing entity ObjectReference
Cylinder 4 Error: Missing entity ObjectReference
Cylinder 3 Error: Missing entity ObjectReference
Cylinder 2 Error: Missing entity ObjectReference
Cylinder 1 Error: Missing entity ObjectReference

I can't select any failures (oil leak or other failures) in SimDirector either, the selection menu is simply empty.

Is that only for me that way? What am I doing wrong?
Or has the error existed for more than 2 years and could not be fixed?

Best regards
andi20
Greetings
andi20 (Jörg)
User avatar
Martyson
Posts: 15173
Joined: Sun Mar 25, 2012 11:08 am

Re: FailureAction does not work since P3DV5.1.

Post by Martyson »

Hello andi20 ,

Did you do a full P3D product install?

Can you start P3D's default flight and Arm Failures?
Best Regards,
Vaughan Martell PP-ASEL (KDTW)
andi20
Posts: 10
Joined: Fri Jun 18, 2021 12:20 pm

Re: FailureAction does not work since P3DV5.1.

Post by andi20 »

With each version (5.0 to 5.4) I have always completely uninstalled the predecessor and reinstalled the current P3d.

In flight mode you can also activate any failure, but it doesn't work in SimDirector.
https://andi20.ch/p3d/failureaction/FailureFlight.jpg

Try it yourself:
Open the Simdirector, create a new flight with "New" and create a FailureAction in it.
Now try to select a system that should fail in the settings of the FailureAction (under "System").
You will see this: https://andi20.ch/p3d/failureaction/FailureAction.jpg
(Under "System" everything is empty!)

Do the same with P3dV4.5, or P3dV5.0, you will see this: https://andi20.ch/p3d/failureaction/FailureActionV5.jpg
(Under "System" an action is already selected, click on the arrow on the right to bring up the complete list of possible failures!)

- - - - -

The difference between Flight and SimDirector FailureAction is big:

In flight mode, an "oil leak" causes the oil to be gone within seconds and the engine to fail. There is only 100% = no leak, or 0%, big leak.

In SimDirector I can set that Oil-Leak has 2% failure (98% OK), so only very little oil flows out, the engine still works for 30 minutes or more.
Greetings
andi20 (Jörg)
User avatar
Martyson
Posts: 15173
Joined: Sun Mar 25, 2012 11:08 am

Re: FailureAction does not work since P3DV5.1.

Post by Martyson »

Hi andi20,

I have not used SimDirector for a L O N G time but I gave it a quick look just now.
Failures are listed (screenshot).

I am still using P3Dv5.3.17.28160 because my Add-on products are not all updated for P3Dv5.4 yet.

Just for information:
How to Post Screenshots (by Chris Metel):
https://www.prepar3d.com/forum/viewtopi ... 3&t=141933


Image
Best Regards,
Vaughan Martell PP-ASEL (KDTW)
andi20
Posts: 10
Joined: Fri Jun 18, 2021 12:20 pm

Re: FailureAction does not work since P3DV5.1.

Post by andi20 »

Unusual. What am I doing wrong when uninstalling and reinstalling?
Do I still have to delete any registry entries after uninstalling?

Which file is responsible for the FailureActions? A dll or a cfg? Can I delete this separately, reinstall?
Greetings
andi20 (Jörg)
Post Reply