Application: Prepar3D.exe
Framework Version: v4.0.30319
Description: The process was terminated due to an unhandled exception.
Exception Info: exception code c0000005, exception address 5E198058
Faulting application name: Prepar3D.exe, version: 3.3.5.17625, time stamp: 0x5758bb31
Faulting module name: api.dll, version: 3.3.5.17625, time stamp: 0x5758bbad
Exception code: 0xc0000005
Fault offset: 0x00128058
Faulting process id: 0x2290
Faulting application start time: 0x01d1d47634b33e43
Faulting application path: E:\P3D\Prepar3D.exe
Faulting module path: E:\P3D\api.dll
Report Id: 84c06f64-d19c-443e-a878-9161d70f4441
Faulting package full name:
Faulting package-relative application ID:
Out of nothing.
I was on the ILS23 into LSGG, addons of course installed.
I don't think it was an OOM, as I had 900mb free on FAP.
Addons:
FSDT LSGG
PMDG 737
Addon mesh
FTX Global
UTX2 for EU
Now I am really pissed, as this is apparently what others also experienced, however I am not really sure if this is the same problem.
A nice calm flight, and then...
Re: A nice calm flight, and then...
Were you in 2D or VC?
Did you click to pop-up the PFD?
Did you click to pop-up the PFD?
Best Regards,
Vaughan Martell PP-ASEL (KDTW)
Vaughan Martell PP-ASEL (KDTW)
Re: A nice calm flight, and then...
VC.
No click, only flying (hands on yoke and throttle, feet on pedals ;-) ).
I might have pressed some button on the yoke, some of which of course trigger some functions like PTT...
No click, only flying (hands on yoke and throttle, feet on pedals ;-) ).
I might have pressed some button on the yoke, some of which of course trigger some functions like PTT...
-
Mike LM
Re: A nice calm flight, and then...
Kosta -
The OOM message is a different one, so this is definitely a different error.
Go through your add-ons and see if any of those may be causing the error. Uninstall half, and try the flight a few times. If you don't see the error, then enable add-ons until you do. If you still see the error, disable half of those and try again. Keep repeating until you find the "problem add-on".
- Mike
The OOM message is a different one, so this is definitely a different error.
Go through your add-ons and see if any of those may be causing the error. Uninstall half, and try the flight a few times. If you don't see the error, then enable add-ons until you do. If you still see the error, disable half of those and try again. Keep repeating until you find the "problem add-on".
- Mike
Re: A nice calm flight, and then...
Hi Mike,
Very much aware of such or similar procedures, been around a while.
I reinstalled the P3D once more and repeated the flight. Went OK, but I did not use VATSIM and also was only on my MSFF2 joystick, and not my complete PFC/MFG hardware.
I have to when I get a chance, to try the same situation I did when it crashed. What addons are concerned, the (software-)setup is one and the same.
Very much aware of such or similar procedures, been around a while.
I reinstalled the P3D once more and repeated the flight. Went OK, but I did not use VATSIM and also was only on my MSFF2 joystick, and not my complete PFC/MFG hardware.
I have to when I get a chance, to try the same situation I did when it crashed. What addons are concerned, the (software-)setup is one and the same.
