Polar Region
-
- Posts: 4
- Joined: Sun Aug 20, 2017 7:31 am
Polar Region
Dear LM,
I had a hard time flying over the north-pole, in fact I couldnt complete it at all because of enormous VAS-usage of the simulation (v3.4).
Are there any chances to get a full working polar region in v4 and further on?
I understand that most of your customers dont have the urgent training need to fly trans-polar but on the other hand - if you sell a "whole earth training environment", "accurate topography" and "worldwide vector data" than it should be complete, including polar regions, shouldnt it?
Best
Alexander Mattheis
I had a hard time flying over the north-pole, in fact I couldnt complete it at all because of enormous VAS-usage of the simulation (v3.4).
Are there any chances to get a full working polar region in v4 and further on?
I understand that most of your customers dont have the urgent training need to fly trans-polar but on the other hand - if you sell a "whole earth training environment", "accurate topography" and "worldwide vector data" than it should be complete, including polar regions, shouldnt it?
Best
Alexander Mattheis
- Rob McCarthy
- Lockheed Martin
- Posts: 3703
- Joined: Wed Aug 24, 2011 1:37 pm
Re: Polar Region
Version 3 will be more sensitive to memory increases especially when using add-ons. In version 4 you will not be constrained to 4gb of VAS. This will most likely alleviate the memory constraints you are experiencing in the polar regions.
Regards,
Rob McCarthy
Regards,
Rob McCarthy
Rob McCarthy
Prepar3D® Core Lead
Prepar3D® Core Lead
-
- Posts: 4
- Joined: Sun Aug 20, 2017 7:31 am
Re: Polar Region
Thank you, Rob
Its sadly not just about the VAS - I encounter scenery problems up there, I attached you a picture.http://prntscr.com/gbdhlx
Regards,
Alexander
Its sadly not just about the VAS - I encounter scenery problems up there, I attached you a picture.http://prntscr.com/gbdhlx
Regards,
Alexander
- Rob McCarthy
- Lockheed Martin
- Posts: 3703
- Joined: Wed Aug 24, 2011 1:37 pm
Re: Polar Region
Alexander,
The accuracy of scenery areas is dependent on data resolution. Can you post a more clear screenshot of the specific issues you are seeing. Screenshots can be captured in Prepar3D by pressing the 'v' key.
Regards,
Rob McCarthy
The accuracy of scenery areas is dependent on data resolution. Can you post a more clear screenshot of the specific issues you are seeing. Screenshots can be captured in Prepar3D by pressing the 'v' key.
Regards,
Rob McCarthy
Rob McCarthy
Prepar3D® Core Lead
Prepar3D® Core Lead
-
- Posts: 4
- Joined: Sun Aug 20, 2017 7:31 am
Re: Polar Region
Dear Rob,
here are some Screenshots of the Polar-Region problem I talked about.
http://prntscr.com/ggq7p3
http://prntscr.com/ggq7tx
http://prntscr.com/ggq7xz
http://prntscr.com/ggq82k
http://prntscr.com/ggq8a2
Best,
Alexander
here are some Screenshots of the Polar-Region problem I talked about.
http://prntscr.com/ggq7p3
http://prntscr.com/ggq7tx
http://prntscr.com/ggq7xz
http://prntscr.com/ggq82k
http://prntscr.com/ggq8a2
Best,
Alexander
- Rob McCarthy
- Lockheed Martin
- Posts: 3703
- Joined: Wed Aug 24, 2011 1:37 pm
Re: Polar Region
Are you seeing this with default content or are scenery add-ons installed? Also when do you see this gap appear? Does it only appear after crossing over the pole?
Regards,
Rob McCarthy
Regards,
Rob McCarthy
Rob McCarthy
Prepar3D® Core Lead
Prepar3D® Core Lead
-
- Posts: 4
- Joined: Sun Aug 20, 2017 7:31 am
Re: Polar Region
I have FTX Global / Vector / openLC EU/NA installed. No other scenery for this region is installed. The gap shows up within 30 minutes from departing ENSB to the north.
Best,
Alexander Mattheis
Best,
Alexander Mattheis
Re: Polar Region
Is it fully possible to make a transpolar flight in v4? AFAIK in previous versions (or MSFS maybe) it was not possible.
Best regards,
Wanthuyr Filho
Wanthuyr Filho
Re: Polar Region
I haven't tried on v4 yet, but have made successful trans-polar flights Svarlbard-Fairbanks in my Phenom 300 using default scenery. What I would like is Aurora Borealis - anyone know if there is an addon for that?
- Rob McCarthy
- Lockheed Martin
- Posts: 3703
- Joined: Wed Aug 24, 2011 1:37 pm
Re: Polar Region
We're having trouble reproducing this issue on our end. To rule out an add-on potentially causing this could you run through our general debugging steps and see if the issue persists? viewtopic.php?f=6312&t=123246
Regards,
Rob McCarthy
Regards,
Rob McCarthy
Rob McCarthy
Prepar3D® Core Lead
Prepar3D® Core Lead