Search found 1156 matches

by WarpD
Tue May 28, 2019 12:51 am
Forum: SimConnect Interface Questions
Topic: [RESOLVED] Simconnect not working v4.5
Replies: 23
Views: 5587

Re: Simconnect not working v4.5

The FSX SimConnect is 32-bit and I'm uncertain that it can interact with the 64-bit sim.
by WarpD
Mon May 27, 2019 3:19 pm
Forum: SimConnect Interface Questions
Topic: [RESOLVED] Simconnect not working v4.5
Replies: 23
Views: 5587

Re: Simconnect not working v4.5

Do all of these addons require the FSX version of SimConnect be installed?
by WarpD
Fri May 10, 2019 6:35 pm
Forum: Prepar3D Client Application Questions
Topic: ILS "beams" are visible v4.5
Replies: 6
Views: 1063

Re: ILS "beams" are visible v4.5

That is not a normal sim behavior. You must have an addon that does this.
by WarpD
Mon May 06, 2019 6:06 pm
Forum: Prepar3D Client Application Questions
Topic: P3D V4: Default CESSNA & other aircraft not appearing!!
Replies: 5
Views: 1479

Re: P3D V4: Default CESSNA & other aircraft not appearing!!

All Textron products have been removed from the simulator.
by WarpD
Fri Apr 26, 2019 1:47 am
Forum: Prepar3D Client Application Questions
Topic: Overexposed photo scenery in 4.5 and 4.4
Replies: 12
Views: 2570

Re: Overexposed photo scenery in 4.5 and 4.4

It is because you've cranked the brightness and dropped the saturation. It's going to destroy the color vibrance of the actual textures and highlight any bright areas even more than they would normally be. By dropping the saturation, you're reducing the color levels and then increasing the brightnes...
by WarpD
Wed Apr 24, 2019 6:32 pm
Forum: Prepar3D Client Application Questions
Topic: Overexposed photo scenery in 4.5 and 4.4
Replies: 12
Views: 2570

Re: Overexposed photo scenery in 4.5 and 4.4

Could this be an issue with sky textures being replaced with third party textures? I believe some of the lighting behavior comes from pixel data contained in a sky texture. Of course, I could be completely off on this. Just a thought.
by WarpD
Fri Apr 19, 2019 8:50 pm
Forum: Other Support Questions
Topic: [RESOLVED] Most VORs and ADFs won´t be recignized by the plane anymore. But why?
Replies: 25
Views: 2695

Re: Most VORs and ADFs won´t be recignized by the plane anymore. But why?

MUN is a high altitude VOR/DME that would not be detected at low altitudes, especially on the runway surface.

MIQ is at 426.5 according to sim data and the chart only shows 426.
by WarpD
Thu Apr 18, 2019 4:48 pm
Forum: Other Support Questions
Topic: Problems with F-22 rudder control at high speeds
Replies: 1
Views: 924

Re: Problems with F-22 rudder control at high speeds

All control surfaces lose effectiveness at higher airspeeds. It is essentially a modified bell curve with regards to surface effectiveness. The F22's rudder is behaving correctly.
by WarpD
Sun Apr 14, 2019 12:29 am
Forum: Prepar3D Client Application Questions
Topic: Corrupt Menu
Replies: 5
Views: 895

Re: Corrupt Menu

Looks like anaglyph 3D to me. The old red/blue glasses method of doing 3D.
by WarpD
Sun Apr 07, 2019 1:21 am
Forum: Other Support Questions
Topic: Max altitude/speed in Prepar3D v4
Replies: 2
Views: 909

Re: Max altitude/speed in Prepar3D v4

I believe the altitude limit is around 100 million feet. This is certainly high enough to support orbital dynamics. However, you would have to create a custom flight/physics engine to achieve shuttle behavior.
by WarpD
Tue Apr 02, 2019 8:24 pm
Forum: Other Support Questions
Topic: DME panel not working
Replies: 52
Views: 4947

Re: DME panel not working

There is a folder of fonts in the base Prepar3D folder. Check to ensure they've been installed to the OS.
by WarpD
Mon Apr 01, 2019 11:52 pm
Forum: Other Support Questions
Topic: DME panel not working
Replies: 52
Views: 4947

Re: DME panel not working

I will state it again. If after a fresh install you have the ability to load the AC11... then you are not using a clean install. Rename the folder "Prepar3D v4 Add-ons" in your "Documents" folder before starting Prepar3D. I believe you have addons still installed.
by WarpD
Mon Apr 01, 2019 6:32 pm
Forum: Other Support Questions
Topic: DME panel not working
Replies: 52
Views: 4947

Re: DME panel not working

There is no AC 11 Commander in Prepar3D v4. That is not a default aircraft. The fact that you are loading said aircraft in a new install tells me you have several addons installed on your system already that Prepar3D v4 is seeing.
by WarpD
Sun Mar 31, 2019 8:47 pm
Forum: Other Support Questions
Topic: DME panel not working
Replies: 52
Views: 4947

Re: DME panel not working

Let's get back to basics....

Did you replace the default flight with one of your own? Both the manifold pressure and the prop RPMs are not correct for sitting idle on the ground.
by WarpD
Sun Mar 31, 2019 2:30 pm
Forum: Prepar3D Client Application Questions
Topic: Error message
Replies: 4
Views: 724

Re: Error message

Bonjour, After installing Client, Content and Scenery from P3Dv4.3 to P3DV4.4 I got this error message https://www.noelshack.com/2019-13-6-1553960344-2019-03-30-13-06-03-57.jpg and P3D starts , but without image That's an error message from an addon. This thread has all the answsers: https://prepar...

Go to advanced search