Search found 14 matches

by baldomero123
Sun Feb 05, 2017 8:47 am
Forum: Prepar3D Client Application Questions
Topic: Chinese / Taking off? but it's so easy...
Replies: 1
Views: 273

Re: Chinese / Taking off? but it's so easy...

I must add the following as for Fuel and Payload Fuel : At least on the a/c I fly in (A321-212 from the fleet of Swiss) the fuel is hard-coded, so wherever you fly the tanks are full 100% and nothing can be done. Payload : for PAX A (74), B (74), C(72) the weights according to FuelPlanner should be ...
by baldomero123
Wed Feb 01, 2017 4:35 pm
Forum: Prepar3D Client Application Questions
Topic: Chinese / Taking off? but it's so easy...
Replies: 1
Views: 273

Chinese / Taking off? but it's so easy...

For some days I have been struggling with the throttle and joke, and searching everywhere trying to "discover" the right way of success (ha). Finally I have found it and I put here, for the people so newby as I am, the set that works, Surely who knows more than me (something rather easy) will presen...
by baldomero123
Tue Jan 31, 2017 3:12 pm
Forum: Prepar3D Client Application Questions
Topic: Modifying the fonts of ATC
Replies: 5
Views: 253

Re: Modifying the fonts of ATC

I have started again the P3D and the fonts keep their (large) siza. Are something like the "Modifying the fonts of ATC" over these posts. The only thing unusual I had done was a " Restore" inside P3D that I don't dear to repeat. Good luck.
by baldomero123
Tue Jan 31, 2017 2:29 pm
Forum: Prepar3D Client Application Questions
Topic: Modifying the fonts of ATC
Replies: 5
Views: 253

Re: Modifying the fonts of ATC

I'm now flying then i' l see if the fonts keep being so large and if i find the reason. Bye.
by baldomero123
Tue Jan 31, 2017 7:59 am
Forum: Prepar3D Client Application Questions
Topic: Modifying the fonts of ATC
Replies: 5
Views: 253

Re: Modifying the fonts of ATC

This morning I have started Prepar3d and I have found the surprise that the fonts in ATC have changed, and not to 12 points (the size I use in Word) but to 14 or more. I haven't done anything, so or somedoby with power to do this change has made it or I don't not what has happened. Alleluia! With FM...
by baldomero123
Sat Jan 28, 2017 3:29 pm
Forum: Prepar3D Client Application Questions
Topic: Modifying the fonts of ATC
Replies: 5
Views: 253

Modifying the fonts of ATC

The fonts in the ATC are so small that is very difficult for me to read them. Searching here and there I have fond two possible solutions, but up to now none of them has worked; here are: 1) Download an application, MenuWindow, that friendly will help me to modiiy the fonts in ATC. It hasn't happend...
by baldomero123
Fri Jan 27, 2017 9:47 pm
Forum: Prepar3D Client Application Questions
Topic: [RESOLVED] Adding a gauge
Replies: 6
Views: 334

Re: Adding a gauge

Finally it works! In my PC there are X-FMC in X-Plane; ISG and JSG in FSX. Specially JSG is easy for me, so after some hours it works in P3D and tomorrow I'll do my 1st flight in Prepar3d. Thank you for your help. Bye.
by baldomero123
Fri Jan 27, 2017 9:22 pm
Forum: Prepar3D Client Application Questions
Topic: [RESOLVED] Adding a gauge
Replies: 6
Views: 334

Re: Adding a gauge

I agree with you, since some gauges are added without a problem and others...I refer to Prepar3d because in FSX one could add whatever you want. I'm very interested in putting a FMC easy to read so I'll try here and there. It seems that ISG is not very friend with Prepar3D. I'll keep searching. Than...
by baldomero123
Fri Jan 27, 2017 6:36 pm
Forum: Prepar3D Client Application Questions
Topic: [RESOLVED] Adding a gauge
Replies: 6
Views: 334

Re: Adding a gauge

Thank you both for your answer. As for the plane is has been downloaded with a lot of planes "Swiss". They are rather similar to A321. The planes, free, are both for FSX and P3D. Well, I will do my best to make it appear on the panel. Thanks.
by baldomero123
Fri Jan 27, 2017 4:05 pm
Forum: Prepar3D Client Application Questions
Topic: [RESOLVED] Adding a gauge
Replies: 6
Views: 334

[RESOLVED] Adding a gauge

I was used to a Radioaltimeter and an other FMS different to this that comes by default, so I have tried to put them in an a/c of Prepar3d, A321-212, as I have made many times in FSX: entering the lines in their place in Panel.cfg and copying the gauges from the Gauges in FSX into the same folder in...
by baldomero123
Thu Jan 26, 2017 7:16 pm
Forum: Hardware Specific Questions
Topic: <My joystick doesn't work at all.
Replies: 1
Views: 211

Re: <My joystick doesn't work at all.

Finally I got it!! Firstly I have deleted every mention to "Elevator trim" in "Calibration" (elevator trim, elevator trim axis, ; I had not less than three!!). I went also to FSUIPC and calibrate there also. I don't know now which of them has been the solution. In first place, of course, having clea...
by baldomero123
Thu Jan 26, 2017 3:46 pm
Forum: Hardware Specific Questions
Topic: <My joystick doesn't work at all.
Replies: 1
Views: 211

<My joystick doesn't work at all.

A month ago I have installed P3D v3 and however I have tried a lot of times, my joystick Logitech Attack 3 doesn't work at all. In "Settings" Calibration appears as Joystick mine, but when a move the axis nothing happens. I go to Calibration of keys / buttons and there appears: Elevator axis ...Y ax...
by baldomero123
Wed Jan 11, 2017 7:44 pm
Forum: Prepar3D Client Application Questions
Topic: Adding aircrafts from Simobjects->Aircrafts
Replies: 1
Views: 144

Re: Adding aircrafts from Simobjects->Aircrafts

My previous wuestion is a nonsense. Every a/c in Simobjects is present in default Prepar3d. Excuse me.
by baldomero123
Wed Jan 11, 2017 3:47 pm
Forum: Prepar3D Client Application Questions
Topic: Adding aircrafts from Simobjects->Aircrafts
Replies: 1
Views: 144

Adding aircrafts from Simobjects->Aircrafts

Good afternoon and my best greeting in my first post: Many of the a/c present by default are of no interest for me, but many present in simobjects->aircrafts I'm interested in them. How can I make some a/c in Simobjects->... to be present when i open Prepar3D? Surely removing a/c I'm not interested ...

Go to advanced search